How to Set up a Tub: Install an Acrylic Bathtub as Well as Bathtub Surround
How to Set up a Tub: Install an Acrylic Bathtub as Well as Bathtub Surround
Blog Article
This article following next involving Installing A Bathtub is highly remarkable. Give it a go and draw your own personal findings.
Mounting a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, and occasionally, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably tough job. If the old tub is readily available, the task can move easily; if you have to open up a wall to eliminate the old bathtub and place the new tub, the task is much harder. In either situation, the project is within a house handyman's abilities, although you will require a helper to leave the old tub as well as embeded in the new one. Make certain you have certified on your own for the job as well as fit attempting it. As opposed to working with a professional to take control of a halfway-completed project, it is better to think about using one before you begin. Opportunities are you may need an expert plumber to make tube connections.
This short article will aid you install a new tub in your washroom if you have already gotten a brand-new bathtub and don't require to transform the arrangement of your previous water system pipelines.
Your tools and product list must consist of the following:
Planning for the Installation
First of all, the sustaining structure supplied with the bath needs to be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to avoid stress on the bathtub.
Fit the versatile faucet connectors to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final position.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing taps can be rather problematic as a result of the limited accessibility that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Using both wood boards under its feet, put the tub in the required position. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to make certain that the bath tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the tub until the level checks out level.
To mount taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the same for the various other tap.
Switch on the water and examine all joints as well as brand-new pipework for leaks and tighten them if needed. Fill up the bath tub as well as also examine the overflow outlet and also the typical outlet for leakages.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait till the bath tub has been used a minimum of when as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers are in location in between the faucet and the sink. Protect the faucet in position with the supplier provided backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet connectors. The former type must be attached to the faucet ends first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a stiff seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components as well as installations. They are offered in tubes as well as cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the bath tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealant can fracture rather early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently offered on the market. It is recommended to fit the tiles using waterproof or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
As a passionate person who reads on How to Install a Bathtub Yourself, I figured sharing that segment was mandatory. Appreciated our posting? Please share it. Help other people locate it. Thanks a bunch for your time. Kindly visit our blog back soon.
Additional Resources
Report this page