Devices You Need to Install a New Bathtub
Devices You Need to Install a New Bathtub
Blog Article
On this page in the next paragraph you'll find some outstanding data with regards to Installing A Bathtub.
Setting up a bathtub isn't exactly rocket science, yet it does need strong plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bathtub with a brand-new one is likewise a reasonably tough task. If the old bathtub is conveniently obtainable, the task can relocate immediately; if you need to open a wall to remove the old tub and place the brand-new bath tub, the job is a lot harder. In either instance, the job is within a home handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also set in the brand-new one. See to it you have actually certified on your own for the work and also are comfortable attempting it. Instead of employing a professional to take over a halfway-completed project, it is better to consider using one prior to you start. Possibilities are you might require a specialist plumber to make tube links.
This write-up will certainly help you install a new tub in your bathroom if you have already purchased a new tub as well as don't need to alter the setup of your previous water system pipes.
Your tools and product list should make up the following:
Getting ready for the Installment
Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to prevent strain on the tub.
Fit the versatile faucet adapters to the bottom of the two faucets using 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its final setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, then the first thing you ought to do is separate the water supply. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly problematic because of the limited accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipes. Once the supply pipes have been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before proceeding to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using both wood boards under its feet, put the tub in the needed position. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four small factors.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the bathtub until the spirit level reads level.
To mount faucets, fit all-time low of the outermost adaptable faucet connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system as well as inspect all joints as well as brand-new pipework for leakages as well as tighten them if required. Fill up the bathtub and additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bath tub needs to wait up until the tub has been made use of a minimum of once as this will certainly resolve it into its final position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end gives a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washers remain in place between the faucet and also the sink. Protect the faucet in place with the producer supplied backnut. Once the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous kind needs to be connected to the tap ends first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to split a stiff seal, triggering the water to permeate the wall between the bathroom as well as the tiling, causing issues with moisture and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures and installations. They are offered in tubes and cartridges, and also can securing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill the tub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can crack rather very early if you do not consider this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly offered on the market. It is recommended to fit the ceramic tiles using waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I stumbled upon that blog post about Installing A Bathtub when perusing the web. Kindly take a moment to distribute this blog entry if you enjoyed it. Thanks for taking the time to read it.
Automated Marketing
Report this page